Explainer

Invisible speakers: what they are, what they mount on and whether they are worth it

An invisible speaker has no cone and no grille: a small exciter makes the surface itself sound, be it plasterboard, glass or wood. Here is what manufacturers confirm, where the limits are and who should buy an ordinary built-in speaker instead.

Updated: 20 November 2026 · smarteg
In short
  • An invisible speaker is an exciter that makes a wall, ceiling or pane of glass produce sound; there is no cone and no grille.
  • Ekinex has models for three materials: DRYWALL (plasterboard up to 16 mm), GLASS (glass up to 12 mm) and WOOD (wood 18–25 mm).
  • Bass is limited, so makers offer subwoofers; you also need a separate amplifier (POWER 1 for Ekinex), and installation happens before finishing.
  • We found no explicit approval for wet rooms from any manufacturer, and none of those we checked lists tile as a covering.
  • Verdict: worth it when no grille may show and the renovation is still ahead; with finished walls or in a bathroom, buy an ordinary built-in speaker.

What it is

An ordinary speaker has a cone that moves air. An invisible one does not: an exciter vibrates a flat surface, and the surface itself makes the sound. The maker Amina describes this as turning the entire plastered surface into a sound source.

In the maker's words, Ekinex Invisible Player turns the surface it is applied to into an invisible loudspeaker; the stated range is 40–16,000 Hz depending on material. The exciter needs an amplifier and has no cabinet. There are two types: exciters fixed to an existing surface (Ekinex Invisible, which we stock) and ready-made panels built into the wall and skimmed over (Amina, Stealth Acoustics, Sonance, Nakymatone; we do not sell these, the data below is for reference).

roomcavity behind the wallamplifierfinish: paint, thin plaster, veneersurface that sounds: drywall, glass or woodtransmitter (exciter) fixed behind
What hides in the wall: finish and the vibrating surface outside, the exciter and a cable to the amplifier behind.

What it mounts on: what Ekinex confirms

ModelMaterial and thicknessFixing and notes
Invisible DRYWALL EK-DW1-AUPlasterboard walls and ceilings up to 16 mm; up to 80 m² per exciterAdhesive EK-3M77-AU; on vertical walls the Vertfix EK-VFX-AU bracket (sold separately)
Invisible GLASS EK-GL1-AUGlass and non-porous materials (e-bond, perspex, lexan, fibreglass) up to 12 mmDouble-sided tape Glassfix EK-GFX-AU; cable duct Coverglass EK-CGL-AU
Invisible WOOD EK-WO1-AUWood 18–25 mmNot for surfaces fixed to the floor or wall; a gap of a few mm is needed behind

For all three exciters the maker states 120 W max / 40 W RMS, 4 ohm and 40–14,000 Hz. There is also the double Invisible TWIN EK-TW1-AU (240 W max / 80 W RMS, 8 ohm). The amplifier is the Ekinex POWER 1 EK-PW1-AU, for 1, 2, 4 or 8 exciters. All of these are in the smarteg catalogue.

Pros and cons, without the gloss

Pros

  • Nothing is visible: no grille, no holes in the ceiling, no separate box.
  • Ekinex exciters exist for plasterboard, glass and wood, so a glass partition or a wood panel can be the speaker.

Cons

  • Bass is limited. Ekinex, Sonance and Nakymatone all offer subwoofers; for full bass, plan one more device.
  • You need a separate amplifier: for Ekinex exciters that is the POWER 1.
  • Installation before finishing: the exciter goes on while the back of the surface is still accessible; it cannot be added to a finished wall.
  • Wet rooms are not confirmed. We found no direct approval for bathrooms from any manufacturer, so do not count on it.
  • The finish is restricted: only a thin layer may go over a panel, and no maker lists tile (see the table below).

Which finish can go on top

Panel-type invisible speakers are finished over, and the layer thickness is tightly limited. The table shows what four makers say about each finish (reference figures; smarteg does not sell these brands).

What you want on topWhat the makers sayVerdict
Filler and paintAmina: 2 mm (above 2–3 mm may affect performance); Stealth Acoustics: up to 1.5 mm (1/16 in); Sonance: up to 3 mm; Nakymatone: about 1.5 mmYes, if the plasterer keeps to the millimetres
WallpaperStealth Acoustics: light wallpaper; Sonance and Nakymatone list wallpaper; Amina's list does notYes, but not with every brand
Veneer, wood panelsVeneer is listed by Amina and Sonance; wood panels by Amina and Nakymatone (thin)Yes, with these brands
MicrocementAmina: 2–3 mmAmina only
Thin stone veneer, marbleListed by Amina onlyAmina only
Leather, fabricLeather is listed by Amina, Sonance and Nakymatone; fabric by AminaYes, with these brands
TileNot listed by any maker we checkedDo not count on it

None of the makers we checked lists tile as a covering. If you want tile or a thick plaster layer, an invisible speaker is not for you. Nakymatone also warns that thick stone walls and dense insulation behind the panel do not work, so check what sits behind the surface before buying.

Who it suits, and who should buy an ordinary built-in speaker

  • Suits: renovation still ahead, plasterboard walls or ceiling, a minimalist interior where a grille would be in the way.
  • Suits: glass partitions or wood panels with a gap behind (Ekinex GLASS and WOOD).
  • Better ordinary: bathroom, tiled kitchen, rooms where you want strong bass without a subwoofer.
  • Better ordinary: finished walls where you can no longer reach the back of the surface.
  • An ordinary built-in speaker has a grille, but it can be painted to match the ceiling or wall, as with the Loxone Install Speaker 7 and Basalte Cielo.

Questions to ask before buying

  1. What is the surface and how thick is it? Compare with 16 mm (DRYWALL), 12 mm (GLASS) or 18–25 mm (WOOD).
  2. Is the wood surface fixed to a wall or floor? That rules out WOOD.
  3. Where does the amplifier go, and how does the cable reach the exciter?
  4. Do you need a subwoofer, and where will it sit?
  5. Will the finish use filler, and how many millimetres does the maker allow?
  6. Is the room damp? Then choose an ordinary speaker with a stated IP rating.

Unsure? Start with in-ceiling speakers; for the professional view, see the hidden speakers guide.

Frequently asked questions

What is an invisible speaker?

It is an exciter fixed to plasterboard, glass or wood that makes the surface itself produce sound; there is no cone and no grille, so nothing shows in the room.

What can Ekinex invisible speakers be mounted on?

DRYWALL on plasterboard up to 16 mm, GLASS on glass and non-porous materials up to 12 mm, WOOD on wood 18–25 mm. A wood surface must not be fixed to the floor or wall.

Do invisible speakers need a subwoofer?

For film and loud music, yes. Bass from invisible speakers is limited, which is why Ekinex, Sonance and Nakymatone offer subwoofers; plan one at the start of the renovation.

Can an invisible speaker be plastered over?

A panel-type one, yes, but only thinly: Stealth Acoustics and Nakymatone allow about 1.5 mm, Amina 2 mm, Sonance up to 3 mm.

Can invisible speakers go under tile?

Do not count on it: none of the makers we checked (Amina, Stealth Acoustics, Sonance, Nakymatone) lists tile as a covering. For a tiled wall choose an ordinary speaker.

Are invisible speakers suitable for a bathroom?

Do not count on it: none of the manufacturer pages we checked explicitly approves wet rooms. In a bathroom, fit an ordinary speaker with a maker-stated IP rating.

Speakers and amplifiers

Ekinex Invisible exciters, the POWER 1 amplifier and other speakers in the catalogue.

Open the catalogue

Read next

Loading...
Back to top